Thermaltake View 37 ARGB Midi Tower - Black Window [CA-1J7-00M1WN-04]

As with the View 28, the left side panel and the lid are made entirely from one piece of transparent acrylic glass, allowing a sweeping view of the interior of the noble cabinet, where powerful hardware and, above all, complex and colorful water cooling systems can be displayed. The View 37 ARGB offers installation options for two 420 radiators. Another highlight is the two vertical PCI slot panels on the back of the tower, where a graphics card can be mounted vertically to display the impressive cooler design of a pixel accelerator.

The Thermaltake View 37 ARGB Midi Tower at a glance:
- Bent side panel in L-shape made of acrylic glass
- Graphics cards up to 41 cm (without front fan), vertical installation possible
- Space for two 420 radiators
- I / O panel with 2x USB 3.0, 2x USB 2.0 and HD audio
- Front with tinted acrylic glass
- 3x pre-installed RGB LED fans including RGB fan lift

Thermaltake View 37 ARGB: Ingenious design & high functionality
The Thermaltake View 37 ARGB is suitable for E-ATX, ATX, Micro ATX and Mini-ITX motherboards. For the installation of the graphics card, the manufacturer has come up with something special. In addition to eight horizontal PCI slot covers, the case has two vertical PCI panels. This makes it possible to showcase a - perhaps even RGB-lit - high-end gaming graphics card impressively. A corresponding holder is already attached to the housing, but can be removed later. Whether horizontal or vertical, the graphics card may be up to 41 inches long.

The front consists for the most part of dark-tinted acrylic glass. In addition, the I / O panel is installed, which in addition to the mandatory audio ports and power / reset buttons has two USB 2.0 and two USB 3.0 ports. Thermaltake uses a small controller to control the RGB lighting of the fans. This is connected to a button on the front of the housing and allows the control of the lighting modes. Alternatively, the button can be used as a reset button and the RGB fan hub can be controlled via a motherboard with ASUS Aura Sync, Gigabyte RGB Fusion, MSI Mystic Light Sync or ASRock Polychrome RGB.

Options for air and water cooling
In addition to the impressive design, Thermaltake has also put a lot of emphasis on functionality in the View 37 ARGB. In the front, a 420-millimeter radiator can be installed, provided you do without the two preinstalled 200-millimeter RGB LED fan. Instead of the drive cage and the mainboard tray pumps and reservoirs / AGBs can be accommodated. The huge side panel allows custom water cooling to be admired from the side and from above - perfectly staged by the stylish RGB lighting of the fans.

If you prefer air cooling, you can also install three smaller 120 or 140 fans instead of the two pre-installed 200-millimeter fans with RGB LED lighting. Right next to the motherboard tray again have three 140- or 120-mm fan space. A 120 or 140 fan can be installed in the rear wall as well as in the case back. A dust filter on the bottom extends over the entire underside and can be pulled out and cleaned at the back. Another dust filter covers the entire front. Behind the mesh grid at the front end of the right side part of the third dust filter is fixed by a magnet.

Space for drives
The power supply is installed in the case back and may be up to 220 millimeters long. In front of the power supply is a hard drive cage for three 2.5- or 3.5-inch data memories. Up to eight additional 2.5-inch SSDs or four 3.5-inch HDDs can be attached behind the mainboard tray without tools.

Note: The PCIe riser cable required for vertical mounting of the graphics card is not included and must be ordered separately. The graphics card should not be higher than two slots when installed vertically.

Technical details:
- Dimensions: 261 x 525 x 538 mm (W x H x D)
- Weight: approx. 11.3 kg
- Material: Steel (SPCC), plastic, acrylic glass
- Color: Black
- Form factor: E-ATX, ATX, Micro-ATX, Mini-ITX
Total possible fan:
- 2x 200 / 3x 140 / 3x 120 mm (front)
- 3x 140 / 3x 120 mm (right side)
- 1x 140 / 1x 120 mm (back)
- 1x 140 / 1x 120 mm (floor)
Preinstalled:
- 2x 200mm ARGB (800rpm, 29.2dB (A), front)
- 1x 140mm ARGB (1000rpm, 27.2dB (A), back)
Radiator mountings (without fan slots):
- 1x max. 420/360 mm (front)
- 1x max. 420/360 mm (right side)
- 1x max. 140/120 mm (back)
- Filter: right side panel, power supply (removable)
Drive Bays:
- 3x 2.5 / 3.5 inches (internal, HDD cage, tool-free mounting)
- 8x 2.5 "or 4x 3.5" drives (internal, behind the MB tray)
- Power supply: 1x standard ATX (optional)
Connections Controller:
- 3x 6-Pin TT RGB (5V)
- 1x 3-pin fan connection
- 1x M / B-In
- 1x LED-out
- Expansion Slots: 8 + 2
I / O panel:
- 2x USB 3.0
- 2x USB 2.0
- 1x 3.5 mm jack (audio out)
- 1x 3.5 mm jack (Mic-In)
- Maximum graphics card length: 410 mm (without front fan)
- Maximum network part length: 220 mm
- Maximum CPU cooler height: 180 mm
Equipment:
- 4x spacers M3 x 6.5 mm
- 4x power supply screws 6-32 x 6 mm
- 24x 3.5-inch HDD screws 6-32 x 6 mm
- 41x motherboard screws M3 x 5 mm
- 8x motherboard screws 6-32 x 33 mm
- 20x fan screws T5 x 10 mm
- 32x Washers / Vibration Dampers (Rubber)
- 10x cable ties
- 1x motherboard speaker
- 1x motherboard signal cable 3-pin ARGB (ASUS / MSI)
- 1x motherboard signal cable 3-pin ARGB (Gigabyte)