Thermaltake Core P7 Design Wandgehuse, Tempered Glass - black [CA-1I2-00F1WN-00]

 To the benefit of this completely free view of the hardware came so far only handy skillful modders, which their housing itself built, but this has now ended with the Core P7.
The Thermaltake Core P7 design wall enclosure at a glance:

Unique design wall housing
Tempered glass front panel
Space for max. 3x 420/480 mm radiators
Modular construction
Vertical installation of graphics card possible
Graphics cards up to max. 57 cm length
Moving additional modules on the sides
The ultimate design wall enclosure

The Thermaltake Core P7 is declared as a full-tower (big-tower), but the term design-wall housing is more appropriate. Even if the Core P7 does not necessarily have to be mounted on the wall, it makes it doubtless there the most impressive impression. The side of the middle module protruding into the space is covered by a pane of tempered glass, while the two wing modules do without cover. These wing modules are slightly separated from the middle module and are held by hinges.

If the Core P7 is used as a stand housing, the wing modules can be positioned at different angles from the main module. From 90 degrees forward to 90 degrees to the rear, everything is possible here and for stabilization and fixing, locks are located at various angles on the hinge. Of course, it is also possible to attach the Core P7 "over corner" to the wall and thus act as an impressive wall decoration. If you are planning to fit a Costum loop in this design case, you have many options to realize the construction of water cooling.
The Thermaltake Core P7: design wall housing for custom water cooling

The Thermaltake Core P7 is predestined for the construction of a custom water cooling system and the two wing modules are designed for this purpose. Both modules can accommodate radiators up to a length of 420 or 480 mm together with the compensating tank and the pump, which allows separate circuits for the CPU and the graphics card to be performed with ease. When using hard-tubes, the Core P7 should be moved as little as possible to avoid breaking or bending.

The main part in the middle takes up the hardware and can hold mainboards up to the E-ATX form factor. A power supply can be installed underneath the mainboard and there is room for data storage or a 420/480 mm radiator to the right of the main board. Reservoirs and pump can be installed between the radiator and the mainboard. If no reservoir is installed on the main body, space for 570 mm long graphics cards remains. These can also be installed vertically.

The Core P7 comes with four brackets for SSDs and HDDs, and these can be installed hidden behind the mainboard tray or next to the motherboard in place of the radiators. For a clean cable management numerous rubber cable grommets are available and CPU coolers can be up to 18 cm high. The I / O panel is located on the right side of the middle segment and has two USB 3.0 and -2.0 ports each.

Note: There is no riser cable for the Core P5, which must be purchased separately. The housing must be assembled. The hardware and WaKü components pictured for illustration are not included!

Technical details:
Dimensions Main part: 570 x 608 x 333 mm (W x H x D)
Dimensions per wing module: 320 x 608 x 333 mm (W x H x D)
Weight: approx. 25.5 kg
Material: steel, plastic, acrylic
Color: Black
Form Factor: E-ATX, ATX, Micro-ATX, Mini-ITX
Fan possible:
4x 120 mm or 3x 140 mm (main part)
4x 120 mm or 3x 140 mm (left module)
4x 120 mm or 3x 140 mm (right module)
Radiators possible:
Max. 1x 480 mm or 420 mm (main part)
Max. 1x 480 mm or 420 mm (left module)
Max. 1x 480 mm or 420 mm (right module)
Drive bays (4 drive brackets are included):
Max. 4x 3.5- or 2.5-inch (next to mainboard)
Max. 3x 3.5- or 2.5-inch (behind MB tray)
Power supply: 1x standard PS2-PSU (optional)
Expansion slots: 8
I / O panel:
2x USB 3.0
2x USB 2.0
1x HD audio
Maximum graphics card length: 280 mm (with reservoir); 570 mm (without reservoir)
Maximum CPU cooler height: 180 mm
Maximum power supply height: 200 mm