Thermaltake View 37 Midi Tower - Black Window [CA-1J7-00M1WN-00]

As with the View 28, the left side panel and the lid are made entirely from one piece of transparent acrylic glass, allowing a sweeping view of the interior of the noble case, in which great hardware and, above all, complex and colorful water cooling can be perfectly displayed. Because the big hit is the ability to install huge radiators with RGB fans next to the mainboard tray, which makes the View 37 a real eye-catcher. Another highlight is the two vertical PCI slots on the back of the tower, where a graphics card can be mounted upright and the impressive cooler design of a pixel accelerator can also be displayed. The View 37 is the perfect showcase case!

The Thermaltake View 37 Midi-Tower at a glance:
- Bent side panel in L-shape made of acrylic glass
- Graphics cards up to 41 cm (without front fan), vertical installation possible
- Space for a 360 mm radiator in the front and 420 on the right side
- I / O panel with 2x USB 3.0, 2x USB 2.0 and HD audio
- Front with tinted acrylic glass
- 2x preinstalled 140 mm riing fans with blue LEDs

Thermaltake View 37: Ingenious design & high functionality
In addition to the impressive design, Thermaltake has also put a lot of emphasis on functionality in the View 37. In the front, a 360-mm radiator can be installed, if you want to do without the pre-installed Thermaltake Riing 140-mm fan with blue LEDs, which is complemented by a second at the back. There is even a 420 mm radiator on the right side in front of the motherboard. For this, the drive cage must be soft, but there are still enough slots for drives. Instead of the cage and the mainboard tray pumps and reservoirs / AGBs can be accommodated. Due to the huge side part, the custom water cooling can be admired from the side and top - perfectly staged by the stylish LED lighting of the Riing fan.

If you prefer air cooling, you can install two 200 mm fans instead of two pre-installed 140 mm Riing RGB fans - or three smaller 120 mm fans. Right next to the motherboard tray again have three 140- or 120-mm fan space.

Midi-Tower or Showcase? The Thermaltake View 37 is both!
For the installation of the graphics card, Thermaltake has also come up with something special for his showcase case. In addition to eight horizontal PCI slot covers, the case has two vertical PCI panels. Up to a maximum of 41 cm long graphics cards can either be installed as usual with the GPU cooler down, or vertically, pointing with the graphics card cooler to the window. This makes it possible to showcase a - perhaps even RGB-lit - high-end gaming graphics card impressively. A corresponding holder is already attached to the housing, but can be removed later.

The combination of design and functionality make the View 37 a first-class midi tower. The design rounded off on both sides and the vertical mounting of the graphics card also give the case a showcase character.
With controller and controller on a PCIe slot bracket

The Midi Tower has dust filters on the side and under the power adapter, which is installed in front of a hard drive cage for three 2.5- or 3.5-inch data storage, and may be up to 220 mm long. Here Thermaltake has also installed four large rubber feet that dampen the vibration of the power supply. Up to eight additional 2.5-inch SSDs or four 3.5-inch HDDs can be attached behind the motherboard tray without tools.

The front consists for the most part of dark-tinted acrylic glass. In addition, the I / O panel is installed, which in addition to the obligatory audio connections and power / reset buttons has two USB 2.0 and two USB 3.0 ports.

Dust filters keep the interior clean
A dust filter on the bottom extends over the entire underside and can be pulled out and cleaned at the back. In addition to the up to 220 mm long optional power supply can be installed there also another up to 140 mm large fan to optimize the airflow with a vertically installed graphics card. Behind the mesh grid at the front end of the right side part of the second dust filter is fixed by a magnet.

Note: The PCIe riser cable required for vertical mounting of the graphics card is not included and must be ordered separately. The graphics card should not be higher than two slots when installed vertically.

Technical details:
- Dimensions: 261 x 538 x 525 mm (W x H x D)
- Weight: approx. 12.7 kg
- Material: Steel (SPCC), plastic, tempered glass
- Color: Black
- Form factor: E-ATX, ATX, Micro-ATX, Mini-ITX
Total possible fan:
- 2x 200 mm, 3x 140/120 mm (front)
- 3x 140/120 mm (right side)
- 1x 120/140 mm (back)
- 1x 120/140 mm (floor)
Preinstalled:
- 1x 140 mm Riing Plus Blue LED (front)
- 1x 140 mm Riing Plus Blue LED (back)
Radiator mountings (without fan slots):
- 1x max. 360 mm (front)
- 1x max. 420 mm (right side)
- 1x max. 120 mm (back)
- Filter: right side panel, power supply (removable)
Drive Bays:
- 3x 2.5 / 3.5 inches (internal, HDD cage, tool-free mounting)
- 8x 2.5 "or 4x 3.5" drives (internal, behind the MB tray)
- Power supply: 1x standard ATX (optional)
- Expansion Slots: 8 + 2
I / O panel:
- 2x USB 3.0
- 2x USB 2.0
- 1x each audio in / out
- Maximum graphics card length: 410 mm (without front fan)
- Maximum network part length: 220 mm
- Maximum CPU cooler height: 180 mm
Equipment:
- 4x spacers M3 x 6.5 mm
- 4x power supply screws 6-32 x 6 mm
- 24x 3.5-inch HDD screws 6-32 x 6 mm
- 41x motherboard screws M3 x 5 mm
- 8x motherboard screws 6-32 x 33 mm
- 20x fan screws T5 x 10 mm
- 32x Washers / Vibration Dampers (Rubber)
- 4x cable ties
- 1x motherboard speaker