12V Laing DDC Pro AGB top and Reservoir []

This pump is the world's first pump which is used in mass-produced watercooled workstations and is ideal for water cooling of processors and suitable electronic components. Due to its size and output can also be used in a variety of applications.
This DC pump is an electronically commutated motor pump, with running times of well over 50,000 hours at 12 volts. The only moving part in a spherical motor pump is a spherically shaped rotor / impeller, which is supported on an ultra-hard, wear-resistant ceramics bearing ball. A conventional shaft with shaft bearings and shaft seals does not exist. The spherical bearing of the rotor / impeller on the ceramics bearing ball provides a variety of advantages: a development of clearance - and thus a noise increase - is not possible in principle. The pump is so quiet about the entire term.
The bearing is self-adjusting. It is lubricated directly by the delivery medium (wet-running pump). No maintenance is undertaken. Since the rotor is always held magnetically in the intended position, smaller dirt particles represent no problem, a blockage of the pump is usually not possible. Even after a long period is given a safe start. Is driven by the permanent magnetic rotor / impeller unit of a magnetic field generated by the surrounding stator. This is built entirely around the rotor. The entire pump is thus with 38 mm only slightly higher than the stator itself so that it fits easily into all conventional PC, Barebone and Mini PC cases. A separate magnetic shielding is usually not necessary. The ball motor principle enables an economical enterprise with comparatively high performances. be controlled by varying the voltage DDC DC pump can be easily and over a wide power range. All wetted parts are corrosion resistant.

This reservoir is designed so that you are installing this in every imaginable shape and can decouple. With the help of decoupling sets (not included), the Laing completely decoupled in 3.5-inch bays are installed, or on the ground, using standard decoupling, are fixed to the floor, or install the better instead of 80mm fans. The paper, all kinds of post-ion feasible, and your projects are now no limits. The reservoir has also 5mm LED drillings for Case Modders. The GTC also has a capacity of 110ml.

Technical data:

Reservoir:
Dimensions (LxWxH): 80 x 80 x 70mm (without connections, without pump)
Weight: 400g
Material: Röhm Plexiglas GS
Mounting: 8x recording decoupling
Connections: 2x G1 / 4 "inch thread
Closing: 1x G1 "-oil sight glass
Volume: 110ml

Pump with cover:
Dimensions: (WxLxH) 62x62x38mm (without connections)
Dimensions Plexi top: 62x62x25mm (without connections)
Motor type: Electronically commutated spherical motor
Rated voltage: 12 V DC voltage
Perm. Voltage range 6 to 13.2 volts
Head at 12V: 3,7 m
max. Flow rate: 420L / h
Fluids: water, water / *
Max System Temperature: 60 ° C
Wetted parts: stainless steel 1.4571, PPS-GF40, EPDM O-rings, aluminum oxide, hard coal

Delivery:
Laing DDC-Pump 12V DDC-1T
Matching screws
Laing DDC Plexi top
Alphacool Laing DDC Reservoir for Laing single attachment

Note: This set will be delivered in parts and has installed itself. Fixing buffer is not included. Please see Article ID: 52 007 also order extra.

Pumps speedometer: With 3-pin Molex connector as pump pulse output (for mainboard or control units)

Note: The pump is the latest revision.

* IMPORTANT: We recommend the use of schmierfähigem addition of water (such as AT Protect Plus or Innovatek Protect). Anti-Corro-Fluid is not recommended.

ATTENTION: Due to the power of the pump may min with only one cycle. 1 cooler will be operated. When operating without load can blow the pump.


Important: The Laing pump electronics are not compatible with water. Please make sure the installation or reinstallation of the pump that the electronics do not come in contact with water. When changing the Laing cover in the correct position of the O-ring and make the filling a Laing pump tank to prevent water overflow. Damage caused by wet electronics are not expanded by Laing.

Why there is a Swiftech Laing and a standard version? Are there differences?

This can be said emphatically "no." Why are there different versions? Here the explanation: Laing produces all of its pumps in Hungary. Once for the overseas market and for the German and European market. The pump itself is thus identical. Some are labeled as Swiftech, as this is the Expulsion of the U.S. market. The other versions are neutral black. In the lower Swiftechpumpen included Entkoplungen is not included in the standard. Otherwise, pump performance, flow, etc., are completely identical.